![\"\"](\"https:\/\/www.supercars.net\/blog\/wp-content\/uploads\/2009\/04\/6yu.jpg\")
<\/a>Giacosa sent his final design to the FIAT experimental workshop on December 15, 1948, resulting in the first prototype running on the test bed in November of 1949. This compact, new powerplant, which yielded a little over 100 horsepower, was then mated to a new prototype 1400 sedan body designed by Pininfarina. Sadly, the new sedan was large, heavy, and underpowered, even with the new V-8 engine. Adding insult to injury, FIAT president Vittorio Valletta didn\u2019t like the new sedan, and liked the hard-to-assemble V-8 engine even less; so the project was scrapped and the new 1400 was pushed in an entirely different direction.<\/p>\n
Despite Valleta\u2019s rejection, Giacosa and Gajal firmly believed that the little V-8 engine had potential. So, in a bold move that would have made Machiavelli proud, Gajal instructed Giacosa to continue development of the V-8 engine, however, under no circumstances was he to let Valletta find out about it!<\/p>\n <\/p>\n A short time later, at the Ristorante Urbani in the center of Torino, a small gathering of experimental department engineers met for a quiet, after-hours dinner. \u201cUnofficially\u201d the topic of conversation was what changes the V-8 engine would \u201chypothetically\u201d need to convert it from a low-revving tourer, into a higher-revving sports car engine. By dessert, it was agreed that the block would be redesigned, the external oil pump relocated, the cylinder heads would be redesigned to accept twin Weber downdraft carburetors, and the combustion chambers revised to boost the compression ratio to 8.5:1. While it is unclear how it happened, not long after this clandestine meeting, an engine fitting this same description was surreptitiously tested in the experimental department and found to produce 115 hp at 6,000 rpm and was capable of turning a reliable 7,000-max rpm. Now, if only they had a place to use it.<\/p>\n Fortunately, Gajal and Giacosa\u2019s prayers were answered in the summer of 1951, when the CSAI (the sporting commission of the Automobile Club of Italy) announced a new Gran Turismo Internazionale Championship (GTI) for cars up to 2,000-cc. The pair knew they already had a great engine for this new category, and all they had to do was convince Valletta to build a suitable car. In August of \u201951, Gayal and Giacosa proposed that FIAT build a prototype sports car that could use an \u201cimproved variant\u201d of the abandoned 2-liter V-8 engine designed for the 1400. This car, they suggested, could be sold to privateers to be campaigned in the new GTI championship against market rivals Alfa Romeo and Lancia, bringing both profit and prestige to FIAT. Valletta and the upper management were hesitant\u2014FIAT had officially turned its back on racing as far back as 1918\u2014but agreed to the production of a single prototype, since the power plant was already developed! However, the management team did not want to overburden the experimental department\u2014which seemed to be working a lot of nights recently\u2014so they agreed, on September 7, that Giorgio Ambrossini\u2019s SIATA workshops would be commissioned to build the prototype. SIATA had much experience building their own racing cars utilizing FIAT components, and so were ideally suited to take on the project.<\/p>\n Within FIAT, this new sports car project was known as the 106 Sport. Interestingly, due to its novel engine design\u2014and perhaps the lack of romance of the term 106 Sport\u2014the car was generally referred to internally as the \u201cV-8.\u201d However, some have speculated that FIAT feared that Ford would enforce its trademark on the term V-8, so they turned the name around and made it \u201c8V\u201d\u2014thus the OttoV\u00fa (Italian for 8V) was born.<\/p>\n Like the 1400 that gave rise to its power plant, the 8V was designed to have a rigid and lightweight unit body, mounted to a minimal frame. As such, the craftsmen at SIATA used two slim oval tubes, joined at the ends by crossmembers for the rudimentary frame. The flowing bodywork was penned by FIAT\u2019s Luigi Rapi and featured an outer steel skin, which was welded to an inner scuttle that was in turn welded to the basic frame. This lightweight, yet rigid, chassis had a wheelbase of 2,400-mm and a front and rear track of 1,290-mm.<\/p>\n For suspension, Giacosa elected to use independent all around, however,\u00a0 on all four corners he chose to use a setup loosely based on a Dubonnet-style system, where the shock absorbers and springs were encased in an oil-filled chamber. However, unlike the Dubonnet-type system, the FIAT system featured shock and spring units encased in a vertically mounted casting, with unequal length upper and lower suspension arms attached directly to this unit, in such a way that it became a single discreet element that could easily be attached or removed from the frame with just six bolts.<\/p>\n <\/p>\n At the rear, the differential unit was solidly mounted to the frame, while the suspension units were bolted to the rear crossmember and benefited from an additional set of telescopic shock absorbers. On the 8V system, which was first developed for the 1937 FIAT Balillas, the geometry of the opposing corner\u2019s control arms is identical, resulting in the outside wheels gaining negative camber during cornering thus keeping the wheels nearly perpendicular to the ground. When completed, the prototype OttoV\u00fa, weighed in at 950-kg (2,054 lbs) and, in the hands of former FIAT Grand Prix driver Carlo Salamano, was capable of a top speed of 200-km\/hr.<\/p>\n In January of 1952, the fully tested 8V prototype was presented to Valletta and the FIAT management team. Though the car showed great promise, the powers that be were still wary of fully committing to a production run of sports cars, this being such a radical departure from FIAT\u2019s traditional offerings of more utilitarian vehicles. However, perhaps seeing the promotional benefits that motor sport could confer, it was agreed that SIATA could be commissioned to build an additional six \u201cproduction\u201d models\u2014three of these were earmarked for competition in the Mille Miglia, two for the Geneva and Torino Motor Shows, and one to be used internally for development and experimentation of a longer wheelbase option.<\/p>\n On March 9, 1952, a special SIATA Daina GS\u2014essentially a Daina body with FIAT 8V drive train and underpinnings\u2014was entered in the Giro di Sicilia for Franco Rol and Gino Munaron. In what was deemed to be a good sign for the 8V\u2019s competition prospects, the pair finished a very promising 2nd in class and 12th overall.<\/p>\n With this confidence-inspiring first test out of the way, the FIAT 8V was first unveiled to an astonished public at the Geneva Motor Show on March 9, 1952. Since the entire project had been conducted in total secrecy\u2014including road testing of the prototype atop FIAT\u2019s private Lingotto roof-top test track\u2014the public and the press were startled to see the FIAT stand include a racing-inspired sports car after FIAT\u2019s nearly 20-year absence from the segment. Needless to say it was the star of both the Geneva and Torino shows.<\/p>\n Come May of that year, three OttoV\u00fas were prepared for the famed Mille Miglia. These three examples were sold to influential privateers (many of whom were FIAT concessionaires) for competition and were entered for the pairings of Vincenzo Aurrichio\/Paolo Bozzini, Supremo Montanari\/Montanari, and Diego Capelli\/Giuseppe Veronelli. The last was that of Diego Capelli, being the car owned by his uncle Ovidio, who was Milan\u2019s largest FIAT retailer and an accomplished racer in his own right.<\/p>\n <\/p>\n While SIATA\u2019s initial foray in the Giro di Sicilia looked promising for FIAT\u2019s chances in the Mille Miglia, sadly circumstances did not work in the company\u2019s favor. The start of the race saw slippery, rainy conditions in Brescia, which caught young Diego out, just five minutes from the starting platform! The damage from the resulting crash was significant enough to put him out of the race immediately and require extensive body repairs to the new FIAT. Soon after, the team of Montanari and Montanari was also caught out by the conditions, leaving the sole remaining 8V of Auricchio and Bozzini to soldier on to a 15th-place overall finish.<\/p>\n It is often said that everything happens for a reason, and while Ovidio Capelli, may have regretted putting his young nephew at the wheel of his new 8V for the Mille Miglia, the resulting damage ultimately changed the historical direction of the entire 8V line. As a result of his nephew\u2019s disastrous start, Capelli had to rebody his new car\u2026the damage was that comprehensive. While Capelli had the choice of any number of carrozzeria to choose from, in the end he elected to give the job to Ugo Zagato and his son Elio. Zagato had forged a name for himself in the prewar years building gorgeous lightweight bodies for many of the most famous racing Alfa Romeos. In the postwar years, Zagato turned much of his attention to building lightweight racers on small displacement FIAT powertrains. These tiny FIAT specials were so good that they carried young Elio Zagato to several Italian national championships.<\/p>\n Setting to work on Capelli\u2019s car, Zagato peeled off the outer steel skin, and leaving just the bulkhead, crafted a new, aluminum GT bodywork, reminiscent of some of their earlier bespoke Mille Miglia models. This lithe new creation was completed in a mere 15 days and cut nearly 100-kg from the factory 8V\u2019s curb weight.<\/p>\n <\/p>\n With Zagato\u2019s amazing turnaround time, Ovidio Capelli was able to enter his new FIAT 8V Zagato (Chassis #000002) in the June 1st running of the Coppa della Toscana, where he finished 3rd in class. But a week or so later, on June 12, he entered it in the Giro dell\u2019Umbria where he finished 1st in class, claiming the 8V\u2019s maiden victory. From there, Capelli went on to finish 5th overall in that year\u2019s Targa Florio and to claim a stunning overall victory in the arduous Stella Alpina, making him the 1952 Italian GT2000 champion.<\/p>\n Whether the elder Zagato relished this one-off project for Capelli is unknown. However, what is known is that young Elio took a very personal interest in it. Undoubtedly, Elio saw in the 8V, the opportunity to elevate his own racing career from the smaller displacement categories, up to the more prestigious 2-liter ranks and, with Capelli\u2019s fantastic 1952 performances, saw both personal and business opportunities in the OttoV\u00fa. As such, Elio convinced his father that they should purchase three rolling chassis from FIAT and produce their own Zagato version of the 8V. The first of the three chassis were delivered in July 1953, and with input from Rapi on the best way to modify the inner scuttle to accept the aluminum body that Elio helped pen, the first example (chassis #000057) made its debut at the Torino Auto Salon on April 21, 1954.<\/p>\n Elio Zagato raced chassis #057 for the first time at the Coppa delle Sei Ore di Orbassano where, right out of the box, he finished an impressive 2nd in class\u2014he couldn\u2019t have been too disappointed, as he was beat by Carlo Leto di Priolo in Capelli\u2019s old Zagato-rebodied 8V! However, Elio\u2019s first overall victory soon followed on May 21, in the prestigious 6 Ore di Bari. Interestingly, Elio\u2019s on-track success in the new 8VZ led to the high-class dilemma that as soon as he won a race, customers wanted to buy that very car right out from under him. This being the case, Elio soon sold #057 and began racing #058; however, it wasn\u2019t long before he had to sell that one as well, such was the competitiveness of the new 8VZ.<\/p>\n With the first three chassis winning so many events and generally being so well received, Zagato committed to production of the 8VZ with another 16 chassis ordered between September 1953 and May 1954. Though it should be noted that the term \u201cproduction\u201d is used rather loosely here, as that each example had minor variations and differences, depending on the requirements of the customer. These variations included differing hood scoops, radiator grills, air outlets on the fenders, and so on.<\/p>\n <\/p>\n While each example had subtle variations, there was one significant and iconic evolution of the 8VZ on the last six chassis to be bodied by Zagato. Starting with chassis #000084 (the car you see on these pages), the 8VZ was given the now-famous \u201cdouble-bubble\u201d roofline. Many have hypothesized that this double-bubble roof was designed to accommodate a taller driver, but in fact, when measured, the portion corresponding to the driver and passenger are the same height as the earlier 8VZ. The real reason for the double-bubble was that it lowered the center section of the roof, yielding a slightly lighter and more aerodynamic roofline that, in turn, offered a diminished frontal area to the wind. Since the 8V had limited horsepower, every advantage was exploited to make the car more slippery to the wind. In addition to this revised roof, these last 8VZs also featured a lower, sleeker body with longer tail fins and nose.<\/p>\n Elio Zagato began racing #084, the first double-bubble, on July 10, 1955, in the Coppa d\u2019Oro delle Dolomiti, where he finished 1st in class and 4th overall. On July 31, Zagato entered it in the Giro della Calabria, where again he finished 1st in class and 5th overall. Zagato finished 18th overall in the grueling Stella Alpina, on August 25, but came right back to finish 2nd overall in the September 11th running of the Coppa InterEuropa at Monza. However, on September 25, Zagato and the lithe 8VZ shocked the competition in Germany when they took 1st overall in the AvD-Preis der Avus, on the famed Avus banking. The piece d\u2019resistance, however, would be that year\u2019s Targa Florio, on October 16, when Zagato and co-driver Capelli drove #084 to a class victory, finishing 11th overall.<\/p>\n For 1956, Chassis #084 was sold to Marino Guarnieri, who raced it four times with his best finish being a 4th in the Coppa InterEuropa. But on October 8th, Guarnieri sold the car to a young Italian who was trying to make a name for himself in racing. That young man was a certain Lodovico Scarfiotti.<\/p>\n Scarfiotti immediately entered #084 in the October 20th running of the Gran Premio di Roma where he finished 2nd in class, and then promptly followed that up with the November 4th Coppa San Marino where he put the GT2000 category on notice with a 1st in class and 2nd overall.<\/p>\n The 1957 season started for Scarfiotti and the 8VZ on March 31 at the Corsa sulle Torricelle where he finished 2nd in class, followed by the April 28th race in Bologna where he finished 3rd. Scarfiotti entered the May 11th running of the Mille Miglia, but uncharacteristically didn\u2019t finish. However, on August 15, he took 1st in class at the Gainsbergrennen and backed it up with a class victory at the Aosta-Gran San Bernardo (September 1) and 2nd overall in the Coppa InterEuropa at Monza on September 8. With a 2nd in class at Pontedecimo on September 29, 1st in class in the Corsa in salita colli Torinese on October 27, and a 2nd in class in the November 30 6 Ore Esso, Scarfiotti easily claimed the 1957 Italian GT2600 Championship.<\/p>\n With offers now coming in to drive other people\u2019s sports cars, Scarfiotti sold #084 to Aldino Aldini for the 1958 season, but Aldini raced it very little and eventually sold it back to Elio Zagato at the end of 1958. Zagato slightly modified the bodywork with a revised nose, tail, and rear wheel covers, and then entered it in the Coppa Sant\u2019Ambroeus at Monza, taking 1st overall, but as always seemed his fate, by October of 1959, he had sold the car to a Californian named Jack Lewarke. Lewarke shipped the car back to Los Angeles where he soon sold it to a 19-year-old kid named Mike Anderson.<\/p>\n <\/p>\n Imagine being a 19-year-old young man in Los Angeles, at the start of the swinging \u201960s, and being able to drive up and down Sunset Boulevard in this gorgeous machine.<\/p>\n One day, not long after purchasing the car, Anderson picked up another young man hitchhiking on Sunset Boulevard. The hitchhiker was a car-crazed enthusiast named Anton Krivanek, who happened to also be a huge fan of the 8V. Anderson thought nothing of the chance meeting and went about his merry way, only to lose control of the 8VZ, two weeks later\u2014on Sunset Boulevard\u2014and promptly flipped the FIAT end-over-end, pulverizing the curvaceous body that had carried Elio Zagato and Lodovico Scarfiotti to so many dominant victories, and breaking his back in the process.<\/p>\n Anderson let the insurance company keep the badly damaged car, which eventually made its way to a wrecking yard. At some point in time, the 8VZ\u2019s remains where bought by an enthusiast with the intent of converting it into a Buick-powered special! As such the body was peeled off and thrown away, the running gear was sold, but eventually the enthusiast lost interest in the project.<\/p>\n Flash forward to the 1980s, and Krivanek\u2014now a specialist in classic car restorations and the 8V\u2014is visiting another 8V expert, Al Johnston. Krivanek points to an 8V frame on the wall and asks Johnston, \u201cWhat\u2019s the story with that?\u201d To which Johnston replies, \u201cThat was an 8V that was wadded up on Sunset Boulevard, back in 1959.\u201d Krivanek had to smile; he knew all too well which car that was, having hitched a ride in it just weeks before its tragic demise.<\/p>\n <\/p>\n Krivanek purchased the frame from Johnston, along with many of the ancillary parts of the car, including the original windshield, which had popped out during the accident and spun across Sunset Boulevard\u2014in one piece! However, Krivanek eventually realized that he was likely never going to have enough money to reunite the original engine with the frame, have a new body constructed, and fully restore the car, so he sold the project to Southern Californian Dan Kolodziejski, who in turn hired Krivanek to return the car to its former glory.<\/p>\n After much searching and a prolonged negotiation, Krivanek was able to locate and purchase the original drive train that came with the car. Since most of the other parts had been saved, Krivanek had everything he needed to fully restore the 8VZ\u2014that is, except the Zagato body. Fortunately, Elio Zagato was keen to see his old warhorse resurrected and so was willing to supervise the project, via the Zagato\u2019s ancestral headquarters in Milan\u2019s Terrazano di Rho.<\/p>\n Through friends at Mazda\u2019s Styling Center in Irvine, California, Krivanek was able to have another surviving 8VZ digitally scanned, so that an exact computer-generated blueprint of the body could be generated. This was then sent to Italy, where in 1999\u20132000, an exacting new body was constructed and reunited with the now-restored original running gear. Elio himself made sure the car was exactly as he had raced it in 1955, when he won both the AVUS and his class in the Targa Florio.<\/p>\n It seemed only too fitting that I should get my chance to drive Zagato and Scarfiotti\u2019s 8VZ in the place where it was ultimately killed and reborn. On a gorgeous, sunny Southern California day\u2014just a stone\u2019s throw from where the car was destroyed\u2014Anton Krivanek and I stood on the beach gazing at the 8V.<\/p>\n Like so many other Zagato creations, the 8VZ has a much more streamlined yet aggressive look, compared to its normal sibling. After having drooled over so many different double-bubbles in my life\u2014Abarth, Aston Martin, Maserati, to name but a few\u2014it\u2019s a little hard for me to believe, as I glide my hand over those sensuous roof bulges, that this very car is the one that started them all.<\/p>\n Everything about the outward appearance of this car was designed with aerodynamic efficiency in mind. Walking up to the driver\u2019s door, I\u2019m greeted by a small button at the end of a flush-mounted chrome strip. Push the button, and the strip pops out to become the door handle\u2014another Zagato hallmark. Sliding into the bucket seat, the interior exudes that wonderful minimalist style that all the great Italian cars from this period seem to possess\u2014quilted leather surface coverings, thin Nardi wood-rimmed steering wheel, and a minimum of black-faced gauges all complete the picture.<\/p>\n Once ensconced behind the wheel, I\u2019m a little surprised at how short the car makes me feel! While I\u2019m 6-feet, the seat sits low in the car and the dashboard binnacle seems kind of tall, leaving me with a feeling of having to look up and over the dash, as opposed to merely through the windshield. Despite the low seating position, the seats are comfortable, with good side support, while the few switches and knobs present are close at hand.<\/p>\n <\/p>\n Not knowing what to expect, in terms of starting procedures, Krivanek explains to me that the 8V is a very simple, straightforward car to drive\u2014simply turn the key on, engage the starter, and the 2-liter V-8 burbles to life. With the door closed and my race belts firmly fastened, I dip the clutch, which protrudes up off the floor along with the brake pedal, and grab hold of the surprisingly tall gearshift lever to select first. With a minimum of accelerator pedal, the 8VZ docilely pulls away, without an iota of fuss.<\/p>\n Accelerating along the road that parallels the sparkling Pacific Ocean, the 8V emits a throaty growl that is a little higher pitched than its bigger Italian brethren, yet still has that same inexplicable aural quality that says, \u201cI am an Italian exotic.\u201d Going up through the gears the 8V\u2019s transmission feels solid and precise. At lower rpm\u2014below 4,000\u2014the 8V feels like a 2-liter. Acceleration is adequate, but nothing to write home to Turin about. No, where the diminutive V-8 comes alive is in the band between 4,000 and its 7,000-rpm redline. It\u2019s in this rarefied territory, where the exhaust note is more earnest and the power is more noticeable.<\/p>\n While the engine would undoubtedly have to have been kept spooled up to be competitive in the likes of the Targa Florio, the car\u2019s remarkable handling would have more than made up for the lack of torque. The combination of the unit body construction with the underlying frame makes the 8V feel surprisingly taut. In fact, it\u2019s very easy to forget that this is a car designed and built in the early \u201950s, where many competition GT cars were bulky and suffered from maladies such as scuttle shake. In many respects, the 8V is very much like a small displacement formula car in that, due to its lack of torque, the car needs to be hustled through the turns. Fortunately, also like a small displacement formula car, the chassis has great torsional rigidity and excels at hustling through the turns. While the four-wheel drum brakes proved more than adequate to stop the lightweight Zagato on our Southern California test drive, it would be interesting to know how they hold up under 12 hours of continual punishment at something like the Mille Miglia.<\/p>\n After pulling the car back in the parking lot and shutting off the engine, I enjoy one last quiet moment alone behind the wheel. Passing my hand one more time over the smooth Nardi steering wheel, I think of Elio Zagato winning the Targa Florio, Scarfiotti flogging away on the Mille Miglia, and even Mike Anderson cartwheeling, end-over-end, down Sunset Boulevard.\u00a0 All this history occurred in this very seat, within the first car to carry the now-famous Zagato double-bubble\u2026like the Grateful Dead said, \u201c\u2026what a long strange trip it\u2019s been.\u201d<\/p>\n<\/a>Secret Society<\/h3>\n
The OttoV\u00fa Is Born<\/h3>\n
<\/a><\/a>Motor Sport Improves the Breed<\/h3>\n
<\/a><\/a>Phoenix Takes Flight<\/h3>\n
<\/a>Win on Domenica, Sell on Lunedi<\/h3>\n
<\/a><\/a>Stepping Stone to Modena<\/h3>\n
<\/a>Sunset Strip<\/h3>\n
<\/a><\/a>Rebirth<\/h3>\n
<\/a>Driving a Legend<\/h3>\n
<\/a><\/a><\/a>